![]() The reminder light will illuminate every 30 cycles. Washer not draining, not spinning out water The Clean Washer Reminder light illuminates to remind you to use the Clean Washer cycle regularly. ![]() What is the Clean Washer Reminder on control panel) Clean Washer Reminder light - Duet® steam washer.Return to this page and add it here using the "I KNOW THE ANSWER!" button above. If you find an answer, please remember to However, replacing your main control board isn’t guaranteed to work, so you might be better off buying a new washing machine instead.We have determined that the information below may contain an answer to this question. The main control board is very difficult to test, so it’s a lot easier to just replace it. If you have checked all of the other components listed above, your final option is to replace the main control board and then see if this solves the problem. If you replace the wire harness, put your washer back together, turn the power back on, and check if the problem has been solved.If the wiring is fine, make sure that the wire harness is securely attached at both ends.If the wiring fails the continuity test, it will need to be replaced. Use a multimeter to check the wiring for continuity.Locate the wire harness that is between the pressure switch and the control module.Turn the power to your washing machine off.To ensure the wires are working correctly, they need to be checked with a multimeter. Sometimes this wire harness can become defective if it gets damaged or corroded. There is a wire harness between the pressure switch and the control module. Reattach the pipe and check if the problem has been solved.If it isn’t blocked, move on to the next step. Locate the air trap pipe (check your manual if necessary).When the pipe gets clogged, it cannot catch air, which will make it defective. The air trap pipe can become clogged with soapy foam and moisture, which can then make the F03/E01 error code appear on your washing machine’s display. If you replace the sensor, put your washer back together, and check if the problem has been solved.If it does have continuity, reattach it in your washer, and move on to the next step. If the sensor doesn’t have continuity, it is faulty and will need to be replaced.Use a multimeter to check if the sensor has continuity.Unplug the wires connected to the sensor.Locate the sensor (check your manual if necessary).Here’s how to check the water level sensor: When it becomes faulty, your washing machine will stop working, and the F03/E01 error code might appear. The sensor monitors how much water is in your washing machine and then tells the control board to allow more water in or stop the water from flowing in. The next step is to check the water level sensor. Reattach the hose and check if the error code has gone. ![]() If it isn’t damaged, disconnect it from the pressure transducer, and check if there are any blockages.If it is damaged, it will need to be replaced. Check the hose to make sure it’s not damaged in any way.Sometimes it can become bent, clogged, or damaged in some other way, and the F03/E01 error code will appear. The next step is to check the water level pressure hose that is located between the pressure switch and the air trap. ![]() After 15 minutes, turn your washer back on, and check if the problem has been solved.You can either switch it off at the wall or turn the circuit breaker off. Sometimes the error code can show when it shouldn’t, and a simple reset will remove the error code and let you use your washer again. The best place to start is to do a simple reset of your washer. This guide covers all major LG washer models, including: Now that we know what the error code means, let’s try to fix it. Most of the time, this error code is a result of a faulty sensor, hose, or brand pipe. If your washer doesn’t get enough water, it will not be able to work correctly. The error code F03/E01 indicates a problem with the water level. Thankfully, removing this error code is usually quite straightforward, and you can do it yourself without having to call a technician.īefore we give you instructions for how to check the likely causes, let’s start by explaining what the error code means. If your Whirlpool washer is showing the F3/E1 error code, this guide will help you find the reason it is showing and how you can fix the problem.
0 Comments
Leave a Reply. |